Search results for 'p 009a'

The 9947EO is an exit only concealed vertical rod device for use on single or double metal doors.
UL listed for Panic Exit Hardware.
Devices are ANSI A156.3 – 2001 Grade 1.

The 9947 device has a grooved mechanism case.

This Device is a 9947EO-3'-US26D - Satin Chrome 3 Foot Device

The concealed vertical rod device is non-handed
Door Height Vertical Rods: Round 2-piece adjustable rods Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm).
Bottom rod adjustable 35-5/8" (905 mm) to 49-5/8" (1260 mm).
Extension rod kits available for doors over 8'4" (2533mm).
Dogging Feature: Hex key dogging standard
Latch Bolt: Deadlocking Top & Bottom Bolt, 5/8" (16mm) throw
Strike: Top - 338 Unfinished, Bottom 385A - Unfinished

DOWNLOADS
Data Sheet

Tubelite Bottom Pivot Set
Includes Top P795L/R Frame Portion Top P795DB Door Portion
Standard 3/16" Inset Mount Specify Left or Right Hand

DOWNLOADS
Brochure

Tubelite Intermediate Pivot Set
Includes Intermediate P795I L/R Frame and Door Portion
Standard 3/16" Inset Mount Specify Left or Right Hand

DOWNLOADS
Brochure

Door sweeps are surface applied to the interior face of a door.
They are commonly used on the interior of out swing doors. 
Sweeps Screw Applied
Aluminum/Vinyl Sweep

P1275 = Sweep Length is 36"

P1276 = Sweep Length is 42"

DOWNLOADS
Sweep Cut Sheet

Seals gaps up to 1” (25 mm)
Lowest profile, 1 9/16” (40 mm)
Minor installation adjustability, 1/16” (2 mm)
Includes self-drilling, 1” mounting screws with combo Phillips & Hex head
Screw Applied - Cut to length - Sold at 48" Long to fit any size door

Cut to size using common tools
Enhanced vertical adjustability for hassle-free installation
Easy install screw-on end caps
Interior or exterior installation

Current discontinued "OLD" Version inventory Includes: (seen in last image)
- 1 @ 36" Clear Anodized
- 1 @ 36" Dk. Bronze  Anodized
- 5 @ 48" Dk. Bronze Anodized

DOWNLOADS
Xcluder Sweep Submittal Sheet
Xcluder Install Instructions

Norton 700 Touchless Actuator Single gang AND double gang packaged together The sensor requires movement for activation Motion Sensor 0"-4" range 0-35 Second Variable Hold Satin Stainless Steel Dimensions: 3" W x 4-3/4" H (Single), 4-1/2" W x 4-1/2" H (Double) Compatible with the following Norton operators: 5600 Series, 5700 Series (5740K3), 5800 Series (ADAEZ), 6000 Series, and 6300 Series Please Note: You Get ONE Switch and two faceplates in the box.

DOWNLOADS
INSTALLATION INSTRUCTIONS

These protective posts are designed to create a defensive barrier that allows for interactions while easing the concerns of your employees and customers.
The ideal solution to protect your staff and customers from the rapid spread of airborne bacterial germs and viruses caused by sneezing and coughing.
Used to separate restaurant booths, counters, office desks, banks, retail store cashier sections, or just about anywhere you can think of.

Diameter: 1" dia. tube.
Finish: Brushed (satin) stainless steel - US32D
Height: 30" tall - Can be recut to any length. (Remove bottom mounting foot and cut with pipe cutter, then reattach foot)  
Adjustable clamps accept 1/4" or 3/8" Glass, Plexi, Lexan. (Note: Glass, Plexi, Lexan is not included)
Glazing Secured by nylon-tipped set screws.
Claps are adjustable to any angle!

Glass recommendation: We recommend setting your vertical posts in place prior to ordering from your local glass company. This will ensure proper sizing and fit.  The glass can extend past the top of the vertical tube to make it taller than 30”. You can also hold the glass up 5” for example or have the glass cut to have a “pass-through”  at the bottom. We recommend you get the glass with polished edges. Please consult a glass company for recommended maximum spans depending on glazing selected.

Note: fasteners NOT included due to varting surface mounting conditions.

If you need a WALL MOUNTED bracket for these vertical posts please click HERE

Wall mounted bracket for our Sneeze Guard / Safety Divider / Partition Posts. Offset to the centerline of the post is 2 1/2". Mounts to wall with two screws and vertical post is held by six set screws. Bracket dimensions: Overall bracket sticks out: 3 7/16" Width: 1 15/16" Height: 2 3/4"

Note: fasteners NOT included due to varting surface mounting conditions.

NOTE: Posts are NOT included but can be purchased HERE

Large Format Interchangeable Core - Schlage 23-030c
6 Pin Temporary Core. - One Bitted Only
Solid Brass
Come with 1 Control Key and 1 Operating Key.
26D finish Only

DOWNLOADS
Key Cylinder Cut Sheet