Search results for 'PO'

Tubelite Intermediate Pivot Set
Includes Intermediate P795I L/R Frame and Door Portion
Standard 3/16" Inset Mount Specify Left or Right Hand

DOWNLOADS
Brochure

Learn More

These protective posts are designed to create a defensive barrier that allows for interactions while easing the concerns of your employees and customers.
The ideal solution to protect your staff and customers from the rapid spread of airborne bacterial germs and viruses caused by sneezing and coughing.
Used to separate restaurant booths, counters, office desks, banks, retail store cashier sections, or just about anywhere you can think of.

Diameter: 1" dia. tube.
Finish: Brushed (satin) stainless steel - US32D
Height: 30" tall - Can be recut to any length. (Remove bottom mounting foot and cut with pipe cutter, then reattach foot)  
Adjustable clamps accept 1/4" or 3/8" Glass, Plexi, Lexan. (Note: Glass, Plexi, Lexan is not included)
Glazing Secured by nylon-tipped set screws.
Claps are adjustable to any angle!

Glass recommendation: We recommend setting your vertical posts in place prior to ordering from your local glass company. This will ensure proper sizing and fit.  The glass can extend past the top of the vertical tube to make it taller than 30”. You can also hold the glass up 5” for example or have the glass cut to have a “pass-through”  at the bottom. We recommend you get the glass with polished edges. Please consult a glass company for recommended maximum spans depending on glazing selected.

Note: fasteners NOT included due to varting surface mounting conditions.

If you need a WALL MOUNTED bracket for these vertical posts please click HERE

Learn More

Wall mounted bracket for our Sneeze Guard / Safety Divider / Partition Posts. Offset to the centerline of the post is 2 1/2". Mounts to wall with two screws and vertical post is held by six set screws. Bracket dimensions: Overall bracket sticks out: 3 7/16" Width: 1 15/16" Height: 2 3/4"

Note: fasteners NOT included due to varting surface mounting conditions.

NOTE: Posts are NOT included but can be purchased HERE

Learn More

Large Format Interchangeable Core - Schlage 23-030c
6 Pin Temporary Core. - One Bitted Only
Solid Brass
Come with 1 Control Key and 1 Operating Key.
26D finish Only

DOWNLOADS
Key Cylinder Cut Sheet

Learn More

The SW300-2CA is a signal switch capable of providing a contact circuit monitoring push bar position. The Switch is field selectable normally open or normally closed. Works with the 3690 series CVR's and 3790 series RIM devices in both manual and electrified.
Installation Manual Learn More

The Command Access MLRK1-FAL17 (MLRK1-FC17) is a cost-effective and straightforward way to upgrade your First Choice 3600/3700, Falcon 1690/1790 series device to motor-driven latch retraction in the field.
UL Listed + 3 Year Warranty

The MLRK1-FAL17 is a robust, straightforward field-installable motorized latch retraction kit for
Falcon Dor-o-Matic 1690/1790 & First Choice 3600/3700 series exit devices. It utilizes a CAT-designed
custom assembly to maximize the pulling force. The only hole you’ll need to drill is the raceway!
It uses our new 1 TOUCH PTS “Push to Set” technology, making post-installation adjustments a
breeze.

FEATURES
Voltage range – 24VDC +/- 10%
System protection – unit shutdown when
voltage exceeds 28VDC
Standard - Average Current Peak: 900mA,
Average Current Hold: 200mA
PTS adjustment – approx. 1/4”

**Don't Forget About A Power Supply With Electric Latch Retraction**

DOWNLOADS
MLRK1 Cut Sheet
MLRK1 Installation Manual

Learn More

Command Access PS202 Power Supply. This Will Power TWO (2) MLRK1 MEL Kit.

PS202 - 110-120VAC input power supplies that deliver (2) amps @ 24VDC to (2) PTC fused outputs. (2) solid-state input triggers, protects system relays from shorts, grounds and surges. Its linear design makes it a perfect match for electric locks, motor driven exit devices, electric strikes, and mag locks.

DOWNLOADS
PS202 Cut Sheet
PS202 Installation Manual

Learn More

Rockwood 107 US3 Straight Pull 8" CTC Polished Brass w/ 1/4"-20 x 21/4" thru bolt & finish washers Limited Quantities Discounted Price!

DOWNLOADS
Cut Sheet Learn More

Von Duprin PS914-2RS series power supply.
The only power supply for use with Von Duprin EL exit devices such as the EL99 & EL9927.
The regulated output power is field selectable for either 24VDC or 12VDC @ 4 amps.
Standard power input 120/240 VAC.
The PS914-2RS replaces the obsolete PS873-2 power supply.

DOWNLOADS
PS914 Data Sheet
Installation Instructions

Learn More