Search results for 'elect and 1>1'

Mill Finish Aluminum Half Saddle Thresholds.

Other Sizes Available on Request.

Bronze, Brass, And other Finish / Base Metal Thresholds Available on Request Please Call.

Anything Over 9 Foot Length is Pickup Only!

E3247 = 5 1/4" x 1/2"

Out Of Stock Till 6-17

As one of the world’s only regenerative power door operators, Norton’s 5845 x NBP (ADA EZ) Series is certified by GreenCircle to reduce energy consumption by as much as 100 percent versus other comparable operators. Available in wireless and plug-in versions and able to fit in the tightest of spaces, the 5800 ADAEZ is simple to install and use.

If the power goes out in the building, this operator will still function.

Need This to Work With An Electric Strike, Card Reader, Fire Panel, Access Control? Grab the ADA1028W WIM Card Sold Seprately..

DOWNLOADS
Installation and Operating Instructions - Push Mount
Installation and Operating Instructions - Pull Mount
WIM Card
Installation Video
Full Catalog
Brochure
Efficiency Plug-in
Efficiency Wireless
Warranty

Typically mounted along the edge of "inactive" door stiles for pair of doors.

Offset: 1/4" / Offset: 1/8"
Flush Bolt Length: 12"
Rod Length: 11" (1/4"-20 thread rod)
Square nylon tip with Beveled Corners Fits in 1/2" (13 mm) Square or Round Strike
Bolt Throw: 5/8"
Backset: 7/8"
5/8" adjustment on rod length
Face Plate: 15/16" Wide x 4-1/4" High with 5/32" radius corner
1/4" Offset is Standard for Tubelite Doors on the edge of stile  -  10-24 thread
1/8" Offset is for the face of the stile   -  10-24 thread

Note: Guides NOT included.

Price is for Single Unit, and not a pair.

DOWNLOADS
Data Sheet

Latch Lock Face Plate For Singles Or Pairs Of Doors, Comes With Screws.

Special Oversize Style Face Plates For Aroyan / Tubelite Doors Only

See 2nd Picture For Handing.

Not Sure Which Power Supply you need?: Power Supply Selector

1 Amp SINGLE Output - ( PSMEL1500-1 )Power Supply for MEL Motorized Latch Retraction capable of operating one (1) 1amp-24VDC panic hardware device.
• In addition, an auxiliary power output shall provide power for accessory devices such as card
readers, key-pads, REX PIRs, electronic timers, relays, etc.
Single MEL Submittal
Single MEL Install Manual

1 Amp DUAL Output - ( PSMEL2000 ) Power Supply for MEL Motorized Latch Retraction capable of operating up to two (2) 1amp-24VDC panic hardware devices simultaneously
• Each lock output shall have an adjustable relock delay timer
• It shall control a pair of doors simultaneously or independently two doors
• Relay for each output to trigger external relays, ADA push plate switches, etc.
• Delayed follower relays shall control automatic door operators for doors that are always locked
or for doors that are unlocked during the business day
• Two un-switched auxiliary voltage outputs shall provide/remove power to the lock outputs when activated
• A programmable FACP interface shall provide power/remove power to the lock outputs when activated
• Shall have LED status indicators monitor AC, FACP status & for lock output wiring supervision
• Intelligent logic shall provide protection against accidental shorting of lock outputs.
Dual MEL Submittal
Dual MEL Install Manual

16 Amp SINGLE Output - ( PSEL1500 ) Power Supply for (solenoid) EL Electric Latch Retraction operates one (1) 16amp-24VDC panic hardware device.
• It is designed to handle the high current surge panic hardware locking devices demand.
• In addition, an auxiliary power output provides power for accessory devices such as card readers, key-pads, REX PIRs, electronic timers, relays, etc.
Single EL Submittal
Single EL Install Manual

16 Amp DUAL Output - ( PSEL3000-2 )DUAL Power Supply for (solenoid) EL Electric Latch Retraction will operate up to two (2) 16amp-24VDC panic hardware devices simultaneously
• It is designed to handle the high current surge panic hardware locking devices demand
• Each lock output has an adjustable relock delay timer
• It will control a pair of doors simultaneously or independently control two individual doors
• It has a follower relay for each output to trigger external relays, ADA push plate switches, etc.
• Delayed follower relays control automatic door operators for doors that are always locked or for doors that are unlocked during the business day
• In addition, two un-switched auxiliary volt-age outputs are provided for powering card readers, keypads, REX PIRs, electronic timers, relays, etc.
• A programmable FACP interface will either provide power or remove power to the lock outputs when activated.
• LED status indicators are provided to monitor AC power, FACP status and for lock output wiring supervision.
• Intelligent logic provides protection against accidental shorting of lock outputs.
Dual EL Submittal
Dual EL Install Manual

Free Shipping On Power Supply When Purchased Along With A First Choice Panic Bar. (Lower 48 States)

All L3 Levers are Factory Ordered, 3-5 weeks lead time.

Utilizing a unique gear system these levers will operate the CVR or Rim exit devices.
All levers are designed to work with most common mortise cylinders.
A security collar is included.
Available in powder coat finishes matching clear aluminum or dark bronze.

DOWNLOADS
Product Literature
Product Literature
Product Templates

Cylinder Cam Information

"M1" Night Latch = Turning key as far as it will go retracts latch. Key MUST be returned to the original position to be removed, leaving the handle locked.
"M3" Hold Back = Turning key one complete rotation unlocks the handle. If Key is removed in this position, the handle stays unlocked, allowing entry anytime. Returning the key to the original position before removing allows the handle to become locked again.
"M2" Passage = The lever is always operable and cannot be locked against entry.
"M0" Inactive = The lever acts as a pull only and is inoperable.
"E1" Electrified Operation Control Option for lever handle - Can be unlocked remotely using 24vDC low amperage (.5 amps)

All L3 Levers are Factory Ordered, 3-5 weeks lead time.

Prefinished .040" Aluminum Sheets in Both Anodized and Painted Finishes.

Available In Full 4' x 8', 4' x 10', and 4' x 12' (All Sheets Pickup Only) or cut sizes pieces may be shipped.
please call to order cut size sheets.

(Larger sheets are available upon request)

Mill Finish Aluminum Saddle Thresholds.

Other Sizes Available on Request.

Bronze, Brass, and other Finish / Base Metal Thresholds Available on Request Please Call.

Anything Over 9 Foot Length is Pickup Only!

E0019 = 4" x 1/2"
E413 = 4" x 1/4"
E277AR = 5" x 1/2" / 7/8"
E513 = 5" x 1/4"
E2550 = 5 1/4" x 1/2"
T2550 = 5 1/4" x 1/2" (Thermal)
E172A = 6" x 1/2"
E613 = 6" x 1/4"
E0009 = 7 1/2" x 1/2"
E2548A = 8" x 1/2"
E2550A = 10" x 1/2"