Search results for 'hold open door closer'

ARM3311 - 1 1/4” diameter with custom center to center offset pull handle.
Each pull handle is fastened with a 5/16 - 18 x 2 1/2" Heavy Duty Thru-Bolt / Button Head Cap Screws for long lasting application for Metal or Wood Doors.
All glass doors come with a decorative thru-bolt for single pull applications

Available in black aluminum or US32D-316 satin stainless (high grade stainless)
Offset posts are available in both US32D-316 satin stainless and black passivate 316 stainless.

Pulls 60" or under have metal caps (Black or Stainless) or Black/Gray plastic capped ends for longer pulls when not seen. .

The recommended minimum length is 18" overall.
The maximum length is 118" overall.

"Standard" Center To Center is Overall Length Minus 6 inches for a standard deduction.

Recommended to add a mid-post to the black aluminum pulls with an overall length of 60" or greater.
Recommended to add a mid-post to stainless pulls with an overall length of 84" or greater.

Any order with a non-centered mid post must be accompanied by the order form sheet available here Order Form

Any pull with 4 or more mid posts please contact Aroyan for pricing and ordering.
Available in single pull mount or Back to Back mounting (BTB)

BTB Pricing is double the price per pull: Example: 36"-45" pull= $ 125 per pull, then select BTB mount and add a qty of 2 pulls into the cart. This will be a price of $250 and this is ONE set of BTB pulls. If you want TWO sets you must add 4 pulls into the cart.

SPECIFICATIONS
Material Dia: 1 1/4"
CTC: Custom please Specify
Base: 1"
Projection: 3 1/8"
Clearance: 2 7/8"
Offset: 1 5/8"

NOTE: Any pull handle over 92" overall in length the shipping method/quote is NOT valid if processed through the online eCommerce sales page. Any pull handle over  104" long must be shipped LTL freight - Please call for updated accurate shipping quotes.

DOWNLOADS
ARM3311 Cut Sheet

Learn More

5800 Series ADAEZ® Operator Wireless Interface Module (WIM)

Norton introduces the Wireless Interface Module, designed to interface all versions of the 5800 Series ADAEZ Low Energy Operator (PRO, PRO PLUS, COMPLETE) with a variety of actuators and systems, including:
Wired or ADAEZ wireless push buttons
ADAEZ wireless remote
Electric lock Fire panel
Access control system
Outside push button disable contact

DOWNLOADS
WIM Card

Learn More

The Von Duprin 99EO is an exit only rim exit device for all types of single or double doors with mullion.
UL listed for Panic Exit Hardware.
Devices are ANSI A156.3 – 2001 Grade 1.

The 99 device has a grooved mechanism case.

This Device is a 99EO-3'-US26D -Satin Chrome 3 Foot Device

The rim device is non-handed
Exit Only function
Trim not included
For doors 1-3/4" to 2-1/4" thick
Strike- 299 – Dull Black.
Dogging Feature- Hex key dogging standard.
Latch Bolt-Deadlocking 3/4“ throw

DOWNLOADS
Data Sheet

Learn More

The 9947EO is an exit only concealed vertical rod device for use on single or double metal doors.
UL listed for Panic Exit Hardware.
Devices are ANSI A156.3 – 2001 Grade 1.

The 9947 device has a grooved mechanism case.

This Device is a 9947EO-3'-US26D - Satin Chrome 3 Foot Device

The concealed vertical rod device is non-handed
Door Height Vertical Rods: Round 2-piece adjustable rods Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm).
Bottom rod adjustable 35-5/8" (905 mm) to 49-5/8" (1260 mm).
Extension rod kits available for doors over 8'4" (2533mm).
Dogging Feature: Hex key dogging standard
Latch Bolt: Deadlocking Top & Bottom Bolt, 5/8" (16mm) throw
Strike: Top - 338 Unfinished, Bottom 385A - Unfinished

DOWNLOADS
Data Sheet

Learn More

Von Duprin EPT-2 / EPT-10 Electrical Power Transfer

EPT-2 = Two 18 gauge wires, Up to 2 AMPS @ 24VDC, with a 16 AMPS Maximum Surge
EPT-10 = TEN 24 gauge wires, Up to 1 AMPS @ 24VDC, with a 16 AMPS Maximum Surge
EPT-10 CON = TEN 24 gauge wires, Up to 1 AMPS @ 24VDC, with a 16 AMPS Maximum Surge with connectors.

DOWNLOADS
Data Sheet
Installation Instructions

Learn More

These protective posts are designed to create a defensive barrier that allows for interactions while easing the concerns of your employees and customers.
The ideal solution to protect your staff and customers from the rapid spread of airborne bacterial germs and viruses caused by sneezing and coughing.
Used to separate restaurant booths, counters, office desks, banks, retail store cashier sections, or just about anywhere you can think of.

Diameter: 1" dia. tube.
Finish: Brushed (satin) stainless steel - US32D
Height: 30" tall - Can be recut to any length. (Remove bottom mounting foot and cut with pipe cutter, then reattach foot)  
Adjustable clamps accept 1/4" or 3/8" Glass, Plexi, Lexan. (Note: Glass, Plexi, Lexan is not included)
Glazing Secured by nylon-tipped set screws.
Claps are adjustable to any angle!

Glass recommendation: We recommend setting your vertical posts in place prior to ordering from your local glass company. This will ensure proper sizing and fit.  The glass can extend past the top of the vertical tube to make it taller than 30”. You can also hold the glass up 5” for example or have the glass cut to have a “pass-through”  at the bottom. We recommend you get the glass with polished edges. Please consult a glass company for recommended maximum spans depending on glazing selected.

Note: fasteners NOT included due to varting surface mounting conditions.

If you need a WALL MOUNTED bracket for these vertical posts please click HERE

Learn More

The SW300-2CA is a signal switch capable of providing a contact circuit monitoring push bar position. The Switch is field selectable normally open or normally closed. Works with the 3690 series CVR's and 3790 series RIM devices in both manual and electrified.
Installation Manual Learn More

Schlage 679-05HM Concealed Door Position Switch

Door position switch is used to detect the open or closed status of an opening and then send this status to a control panel.

Designed for monitoring door positions, roof hatches, gates etc.

• For hollow metal doors and frames
• SPDT Magnetic Switch 
• 0.3 Amps @ 30 VDC.

DOWNLOADS
Cut Sheet
Installation Template

Learn More

This angle drops the closer by 3/4", lowering the closer just enough to clear the top of the closer knuckle if you have a soffit over the top of your frame. Reusing the previous bottom hole loctions on the header.

1" x 1" x 1/8" thick aluminum angle bracket pre-machined for standard closers that measure 9-1/16" CTC wide x 3/4" CTC tall.

Comes with two 12-24 x 1/2" screws to mount the angle to the underside of the header.

Available in both Clear and Dark Bronze Anodized finishes.

DOWNLOADS
Diagram Template

Example Closers To Fit This Bracket:

• Norton 1600 Series
• Dormakaba/Stanley QDC300 Series
• LCN 1250 Series
• Falcon SC61
• Hager 5300
• International 8051-TP

Learn More