Search results for 'el'

BEA / BEA Logic Modules Sensors, Switches, Relays, Timers / Software & Control Hardware BEA 10BR2-900 Logic Module, Sequenced or Simultaneous Relay Activation, 2 Relays

DOWNLOADS
Cut Sheet Learn More

SDC’s 45 series 5/8” latchbolt electric strikes are centerline latch entry strikes designed for use with cylindrical locksets and mortise locksets without deadbolt for both metal and wood frames. 45 series strikes accept 5/8” throw latchbolts or up to 3/4” throw latchbolts with 1/8” door gap.

Designed with round corners for aluminum jambs.
12/24 VDC (+/- 10%) input.  (Please ADD the "BR64XL" - Rectifier If you have AC input)

Comes Standard with: 4 7/8" Radius Corner Clear Anodized Face Plate, Adjustable Alignment, Latch Status "LS" Monitoring, &  Keeper Deadlocked Status.

Fail safe or fail secure functions are field selectable.- (Comes packed as Fail secure)

When used with DC voltage this electric strike is silent - Please ADD the "RMB" - Buzzer to your order if you wish to have an auditable buzzing noise.

Note: Black Finish faceplate is available and as an added part (you will get BOTH clear-628 and black-335 faceplates) if you select the Black Finish at checkout.

BR64XL Rectifier = The SDC BR64XL is a bridge rectifier that converts 12 or 24 volts AC transformer to DC Output. The unit is equipped with 6" wire leads.

DOWNLOADS
Data Sheet

Learn More

The SW300-2CA is a signal switch capable of providing a contact circuit monitoring push bar position. The Switch is field selectable normally open or normally closed. Works with the 3690 series CVR's and 3790 series RIM devices in both manual and electrified.
Installation Manual Learn More

Not Sure Which Power Supply you need?: Power Supply Selector

1 Amp SINGLE Output - ( PSMEL1500-1 )Power Supply for MEL Motorized Latch Retraction capable of operating one (1) 1amp-24VDC panic hardware device.
• In addition, an auxiliary power output shall provide power for accessory devices such as card
readers, key-pads, REX PIRs, electronic timers, relays, etc.
Single MEL Submittal
Single MEL Install Manual

1 Amp DUAL Output - ( PSMEL2000 ) Power Supply for MEL Motorized Latch Retraction capable of operating up to two (2) 1amp-24VDC panic hardware devices simultaneously
• Each lock output shall have an adjustable relock delay timer
• It shall control a pair of doors simultaneously or independently two doors
• Relay for each output to trigger external relays, ADA push plate switches, etc.
• Delayed follower relays shall control automatic door operators for doors that are always locked
or for doors that are unlocked during the business day
• Two un-switched auxiliary voltage outputs shall provide/remove power to the lock outputs when activated
• A programmable FACP interface shall provide power/remove power to the lock outputs when activated
• Shall have LED status indicators monitor AC, FACP status & for lock output wiring supervision
• Intelligent logic shall provide protection against accidental shorting of lock outputs.
Dual MEL Submittal
Dual MEL Install Manual

16 Amp SINGLE Output - ( PSEL1500 ) Power Supply for (solenoid) EL Electric Latch Retraction operates one (1) 16amp-24VDC panic hardware device.
• It is designed to handle the high current surge panic hardware locking devices demand.
• In addition, an auxiliary power output provides power for accessory devices such as card readers, key-pads, REX PIRs, electronic timers, relays, etc.
Single EL Submittal
Single EL Install Manual

16 Amp DUAL Output - ( PSEL3000-2 )DUAL Power Supply for (solenoid) EL Electric Latch Retraction will operate up to two (2) 16amp-24VDC panic hardware devices simultaneously
• It is designed to handle the high current surge panic hardware locking devices demand
• Each lock output has an adjustable relock delay timer
• It will control a pair of doors simultaneously or independently control two individual doors
• It has a follower relay for each output to trigger external relays, ADA push plate switches, etc.
• Delayed follower relays control automatic door operators for doors that are always locked or for doors that are unlocked during the business day
• In addition, two un-switched auxiliary volt-age outputs are provided for powering card readers, keypads, REX PIRs, electronic timers, relays, etc.
• A programmable FACP interface will either provide power or remove power to the lock outputs when activated.
• LED status indicators are provided to monitor AC power, FACP status and for lock output wiring supervision.
• Intelligent logic provides protection against accidental shorting of lock outputs.
Dual EL Submittal
Dual EL Install Manual

Free Shipping On Power Supply When Purchased Along With A First Choice Panic Bar. (Lower 48 States)

Learn More

Command Access PS202 Power Supply. This Will Power TWO (2) MLRK1 MEL Kit.

PS202 - 110-120VAC input power supplies that deliver (2) amps @ 24VDC to (2) PTC fused outputs. (2) solid-state input triggers, protects system relays from shorts, grounds and surges. Its linear design makes it a perfect match for electric locks, motor driven exit devices, electric strikes, and mag locks.

DOWNLOADS
PS202 Cut Sheet
PS202 Installation Manual

Learn More

Tubelite Intermediate Pivot Set
Includes Intermediate P795I L/R Frame and Door Portion
Standard 3/16" Inset Mount Specify Left or Right Hand

DOWNLOADS
Brochure

Learn More

RCI 0161 3/4" Semi-Mortise Rim Strike
The 0161 is a 3/4" semi-mortise electric strike that is designed to operate with Pullman latch rim exit devices.
"08" Is 24 VAC/DC
"05" is 12 VAC/DC
NOTE: Available in US32D Only

The stainless-steel finish creates a sleek attractive architectural appearance. The slotted horizontal holes on the faceplate allow for easy and secure mounting during installation and correct alignment with the exit device. It features a hazard-free radius design.

FEATURES
Energy: 200mA 12VAC/VDC Or 24VAC/VDC (Max at 12VDC)
Strength: 1,500lbf Static 70ft-lb Dynamic
Endurance: 500,000 Cycles
Mode: Fail-Secure
Warranty: 5 Year Limited Warranty

DOWNLOADS
0161 Cut Sheet
0161 Installation Manual

Learn More

The Schlage AL80BD Storeroom Lever is perfect for medical, office, hotel, public buildings, religious, multi-family, retail, and government facilities. Both indoor and outdoor applications

AL series has been discontinued and replaced by the ALX

One left - get it on a DISCOUNTED speical price!

Schlage AL80BD SAT 626 Storeroom Door Lever Set without Small Format Interchangeable Core
- Function Entrance
- Grade 2
- Finish: Satin Chrome - 626
- Handing Reversible
- Backset: 2-3/4"
- Latch Type: Square Corner
- Strike: ANSI Strike 10-025
- Door Thickness 1-3/8" to 1-7/8"
- ANSI Certification: Meets or exceeds A156.2 Series 4000, Grade 2 strength and operational requirements.

DOWNLOADS
AL-Series Catalog
AL-Service Manual
AL-Installation Instructions

Learn More

The SL57HD Continuous Hinge Mounts on the face of a door &fFrame for a perfect solution to hinge replacement.
The HEAVY DUTY Manufacturing and the Lifetime Warranty give you the safety and PEACE OF MIND that you deserve.  

For door thickness 1 3/8"-1 3/4". (For 2"-2 1/4" with optional long barrel nuts.)

NOTE: For Continuous Hinges 95" and over in length the shipping method/quote is NOT valid if processed through the online eCommerce sales page. 120" hinges long must be shipped LTL freight - Please call for updated accurate shipping quotes.

DOWNLOADS
Data Sheet

Learn More